e-Sky USB Simulator Tx - Aerofly Deluxe Compatability?
4 posts
• Page 1 of 1
e-Sky USB Simulator Tx - Aerofly Deluxe Compatability?
by mouthpiec » Thu Sep 28, 2006 11:24 am
Is the e-Sky USB Simulator Tx compatable with the Aerofly Deluxe?
- mouthpiec
- Posts: 2
- Joined: Thu Sep 28, 2006 11:20 am
by aeropal » Sat Jan 13, 2007 9:09 pm
Very interesting . . so are you connecting the Esky controller to a 2nd USB port as described in this ?
"My Slave Interface-Cable or Slave GameCommander don’t work.
Keep in mind that the Patch V1.8.0.23 is mandatory for the USB Slave Cable/GameCommander to work. Here is the Set-Up Procedure:
Make sure you have the Patch Version 1.8.0.23 installed from our download section. When starting Aerofly Professional Deluxe (AFPD) check for this version in the upper left corner of the main menu screen (The screen with the rotating model in the middle).
Start AFPD with only the original USB Interface-Cable or USB GameCommander connected. If the USB Interface-Cable is connected without a transmitter you will get a message saying that no TX was detected — Click O.K.
Connect the USB Slave GameCommander to a free USB port, wait a few seconds and then click on “Calibrateâ€.
In the “Input Device†window click on “Refreshâ€. You will then see “USB Dummy GC #0†— highlight this and click on “Propertiesâ€.
Calibrate as you would with any controller (see manual).
Click on “Controlsâ€. At the bottom of the window click on “Newâ€.
On the left lower section of the window click on the circle displayed at the “USB Interface/Game Commander #2â€.
Proceed with the “Channel Assignment†— Click O.K. when finished.
At the “Aircraft Control Settings†window you will see “New USB/Interface/GC #2†— Assign to Aircraft 1 or 2 and click O.K.
You are now ready to fly."
"My Slave Interface-Cable or Slave GameCommander don’t work.
Keep in mind that the Patch V1.8.0.23 is mandatory for the USB Slave Cable/GameCommander to work. Here is the Set-Up Procedure:
Make sure you have the Patch Version 1.8.0.23 installed from our download section. When starting Aerofly Professional Deluxe (AFPD) check for this version in the upper left corner of the main menu screen (The screen with the rotating model in the middle).
Start AFPD with only the original USB Interface-Cable or USB GameCommander connected. If the USB Interface-Cable is connected without a transmitter you will get a message saying that no TX was detected — Click O.K.
Connect the USB Slave GameCommander to a free USB port, wait a few seconds and then click on “Calibrateâ€.
In the “Input Device†window click on “Refreshâ€. You will then see “USB Dummy GC #0†— highlight this and click on “Propertiesâ€.
Calibrate as you would with any controller (see manual).
Click on “Controlsâ€. At the bottom of the window click on “Newâ€.
On the left lower section of the window click on the circle displayed at the “USB Interface/Game Commander #2â€.
Proceed with the “Channel Assignment†— Click O.K. when finished.
At the “Aircraft Control Settings†window you will see “New USB/Interface/GC #2†— Assign to Aircraft 1 or 2 and click O.K.
You are now ready to fly."
-
-
aeropal - Posts: 205
- Joined: Fri Dec 27, 2002 4:18 am
4 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 39 guests