I just Found FMS like 1 week ago and think it is an awsome simulator..I'm just getting into R/C airplane and hope this helps me to go solo quicker than normal..I have been into R/C Nitro powered car and truck for around 3 yrs it is an awsome hobby.finally decided to gor in the air with my hobby..
Any how i have Also setup a website
AS you all can see the site is new and I'm going to try to Offer alot to the Community.
I have recently just made my first plane for FMS called "White Trainer" available on my site.
i just need a little help with the Par file setups cause when the trainer i built leaves the ground on take of it shoot up on a pretty sharp climb angle..i need help try to fix the amount of climb this plane has..
A hello to all from a new commer to the community..
My First Plane
8 posts
• Page 1 of 1
by trvo » Wed Oct 29, 2003 12:57 pm
Hiya,
By the look of your screenshot you have done a very nice job for your first plane. I haven't flown it yet because I have been having some trouble with FMS and my graphics card recently which means that FMS won't run until I get it sorted.
Keep up the good work
Kind Regards - Trvo
By the look of your screenshot you have done a very nice job for your first plane. I haven't flown it yet because I have been having some trouble with FMS and my graphics card recently which means that FMS won't run until I get it sorted.
Keep up the good work
Kind Regards - Trvo
Please Note: No trees were destroyed in the sending of this contaminant free message. We do however concede that a significant number of electrons may have been inconvenienced. Visit My Website at: http://www.freewebs.com/fmsusers/
-
trvo - Posts: 116
- Joined: Mon Mar 10, 2003 9:20 pm
- Location: Earth
by FreeFlier » Wed Oct 29, 2003 5:29 pm
Nice work eclipsegsxr. The White Trainer flys well, but of course "crys out" for color. The colors appear in the .bmp file but not on the model; I'm no software or Metasequoia person for sure, but I'm sure you can add the coloring.
I did reduce the thrust (line 3) to 8, and increased the CLmin to -1.0 (to allow sustained inverted flight). I do the latter to most FMS models simply because I like inverted flight; not withstanding the fact that many of these models would not maintain inverted flight at all.
The reduced thrust will keep the model on the runway, but the "real" model might just fly the way your model did originally. Many models with "Clark Y" type airfoils will climb with full throttle, fly level at moderate throttle settings, and sink at lower settings.
I also replaced the .wav file with one from an electric model, since I fly electric only, and find the FMS IC .wav file annoying.
Aside from the above I made no other changes and await the coloring of the model.
Congratulations on a fine first FMS model, and by the way, on a fine website. I hope and expect to see more from you.
Thermals,
Stew
I did reduce the thrust (line 3) to 8, and increased the CLmin to -1.0 (to allow sustained inverted flight). I do the latter to most FMS models simply because I like inverted flight; not withstanding the fact that many of these models would not maintain inverted flight at all.
The reduced thrust will keep the model on the runway, but the "real" model might just fly the way your model did originally. Many models with "Clark Y" type airfoils will climb with full throttle, fly level at moderate throttle settings, and sink at lower settings.
I also replaced the .wav file with one from an electric model, since I fly electric only, and find the FMS IC .wav file annoying.
Aside from the above I made no other changes and await the coloring of the model.
Congratulations on a fine first FMS model, and by the way, on a fine website. I hope and expect to see more from you.
Thermals,
Stew
- FreeFlier
- Posts: 53
- Joined: Thu Sep 04, 2003 12:12 am
by ggunners » Thu Oct 30, 2003 4:12 pm
The color of the model will show up when the .x file is changed to point to the right location for the .bmp file.
Open the .x in NotePad
change:
..\\white trainer\\white trainer.bmp
to:
white trainer.bmp
This can be avoided by keeping all model parts in the Metasequoia LE model root directory.
Enjoy the color!
-- ggunners
Open the .x in NotePad
change:
..\\white trainer\\white trainer.bmp
to:
white trainer.bmp
This can be avoided by keeping all model parts in the Metasequoia LE model root directory.
Enjoy the color!
-- ggunners
-
ggunners - Posts: 1480
- Joined: Tue Aug 26, 2003 3:47 pm
- Location: Chantilly, VA USA
by FreeFlier » Thu Oct 30, 2003 7:41 pm
ggunners,
...was unable to find the referenced instruction in note pad (or word pad); is this only available in Metasequoia?. If so, then I'll have to wait for someone else to make the change.
Thanks for the suggestion anyway.
Thermals,
Stew
...was unable to find the referenced instruction in note pad (or word pad); is this only available in Metasequoia?. If so, then I'll have to wait for someone else to make the change.
Thanks for the suggestion anyway.
Thermals,
Stew
- FreeFlier
- Posts: 53
- Joined: Thu Sep 04, 2003 12:12 am
by eclipsegsxr » Fri Oct 31, 2003 6:09 am
free flier
very odd that you say the plane has no coloring for you ..i just rechecked the file on my pc and the color looks and works nicely on my plane on my PC..i do plane to put out more planes.i'm working on a new one at the present time..hope to have it done shortly and will be available on my site..Thanks for the "good job" on my site..it is coming along nicely..hope to have more on it soon.
very odd that you say the plane has no coloring for you ..i just rechecked the file on my pc and the color looks and works nicely on my plane on my PC..i do plane to put out more planes.i'm working on a new one at the present time..hope to have it done shortly and will be available on my site..Thanks for the "good job" on my site..it is coming along nicely..hope to have more on it soon.
- eclipsegsxr
- Posts: 55
- Joined: Tue Oct 14, 2003 6:30 pm
8 posts
• Page 1 of 1
Who is online
Users browsing this forum: Google Adsense [Bot] and 16 guests